供应孙大灯SDD2500A启动电源

产品简介

      启动电源是汽车维修行业必备工具，具有电池充电，车辆启动，焊接等功能。尤其在北方地区冬季使用，会在很大程度上减轻蓄电池的负担，延长蓄电池的使用寿命，给消费者带来极大方便。

一、启动

1、首先确认所被启动的车辆蓄电池电压为12V或24V。正、负极不得接反。12V正极连接线连接到标有12V“+”的位置。24V正极连接线连接到标有24V“+”的位置。负极不分12V/24V均连接在标有起动“-”的位置。

2、用连接线将启动电源和蓄电池正负极对应连接。

3、确认连接无误：打开保护开关将电流调节旋钮拨至**档，开始起动车辆。如起动马力不足可将电流调节旋钮顺时针方向调节。（也可以将电流调节扭直接调至起动档，即**大档）

二、充电

     根据电池电压用连接线接好，确认12V或24V。给12V电池充电将连接线连接在标有12V“+”的位置，给24V电池充电，将连接线接在标有24V“+”的位置。负极均接在标有充电“—”的位置（12V、24V均接在充电“—”的位置）

三、电焊

1、必须将连接线连接在24V位置。正极接在标有24V“+”的位置上，负极接在起动“—”的位置上。

2、调节电流旋钮至焊接位置，也可根据焊条大小顺时针调节电流增大。（也可直接将电流旋钮调至焊接位置）

                                                                                             技术指标

Product Introduction

1、Starting power is necessary tool for vehicle maintenance industry. Its function is battery charging、vehicle starting、and welding etc., especially used in could case. A starting power largely reduces a burden of batteries, prolongs the service life of batteries, and provides a great convenience for consumers.    

一、Starting

1、First of all, confirm the started vehicle battery voltage is 12 V or 24V. Positive and negative can not be connected in reverse. 12V anode is connected to the 12V positive position with “+”mark. 24V cathode is connected to 24V negative position with “+”mark. Negative does not distinguish 12V from 24V. Positive and negative are connected to the starting position with “-” mark.

2、With connection lines, the positive and negative poles of the starting power supplies and batteries are connected correspondingly.

3、Carefully confirm connection: open a protection switch, shift the current regulation knob to first gear; Then begin to start a car. If the starting horsepower is insufficient, clockwise adjust the current adjusting knob.

二、Charge

According to battery voltage, connection lines are connected tightly ,and make confirmation of voltage for 12.0 V or 24 V. Charging a battery with 12 V, make connection line to the 12 V position labeled as “+”. Charging a battery for 24 V, set connection line on 24 V position marked as “+”. Cathodes are all connected to charging position labeled as " - " (12V and 24V both are joined to charging " - " position)

三、Welding

1、A connection line must connect to 24V position. Positive electrode joins to the 24V position labeled as " + ", negative electrodes all are joined to the starting position labeled as “－”

2、Regulate a current knob to a welding position, Also can be based on a welding size, increase clockwise current.

(Also possibly and directly regulate a current knob to the welding position)